Important

This kalkulator gives a starting point for irrigation volume and czas pracy. Actual needs vary with korona, root zone, drainage, irrigation method, upał, wind, and sun. Check long runs in the field.

Sad Irrigation Czas pracy Kalkulator

Q: "Can I use it without a target woda amount?"

"Yes. Leave target woda blank and the kalkulator uses the referencyjny midpoint built from tree age, spacing, and gleba."

Q: "Does tree spacing mean row spacing?"

"In this kalkulator, tree spacing means the distance to the next tree in the same row. It does not calculate row spacing area."

Q: "Does it use weather data or ET?"

"No. It is designed to stay practical by using only tree structure and kroplownik flow."

Q: "Can I switch between metric and US units?"

"Yes. You can switch between m / ft, L / gal, and L/h / gal/h."

Build a referencyjny per-tree woda amount from tree age, spacing, and gleba, then calculate one irrigation czas pracy from kroplownik flow and count.

Because the model does not depend on local weather data, the same logic works in any region.

Uses the referencyjny midpoint automatically Switches between metric and US units Keeps share URLs and the last state Calculates entirely in the brzędyer

Calculate irrigation volume and czas pracy

Even when target woda is blank, you can oszacuj czas pracy from the referencyjny midpoint.
Enter a target woda amount to recalculate czas pracy from that exact value.

Jak używać

Enter tree age, spacing, gleba type, kroplownik flow, and kroplownik count.
Review the referencyjny range and enter a target woda amount if needed. Leave it blank to use the referencyjny midpoint.
Check the czas pracy, per-kroplownik woda, and total flow.
Copy the result or copy the share URL for use in the field.

Examples

Use a manual target woda amount for a 5-year sad tree

Dane wejściowe 5 years old, 4.0 m spacing, loam gleba, 24 L/tree target woda, 2.0 L/h kroplownik flow, 4 emitters

Wynik Referencyjny woda 22 - 33 L/tree, czas pracy 3h00m, per-kroplownik woda 6.0 L

Leave target woda blank to use the referencyjny midpoint

Dane wejściowe 12 years old, 18 ft spacing, clay gleba, target blank, 0.5 gal/h kroplownik flow, 6 emitters

Wynik The referencyjny midpoint is used automatically, czas pracy 5h54m, within the referencyjny range

Słownik

Wiek drzewa

Years since planting. It anchors the referencyjny curve.

Rozstaw drzew

Distance to the next tree in the same row.

Gleba type

A simple way to express woda retention and drainage differences.

Kroplownik

One emitter outlet with a known flow rate.

Referencyjny woda

The starting woda amount built from age, spacing, and gleba.

Czas pracy

The time you run the irrigation line for one wodaing event.

Wzory

Referencyjny midpoint = age-based woda × spacing factor × gleba factor
Referencyjny range = midpoint × 0.8 to 1.2
Total flow = kroplownik flow × count
Czas pracy = target woda ÷ total flow
Per-kroplownik woda = target woda ÷ kroplownik count

How the referencyjny woda is built

Start from tree age, then nudge it with spacing and gleba. No weather data required.

Age anchors

Age	Base woda	Referencyjny spacing
0	3 L/tree	2.0 m
1	6 L/tree	2.2 m
3	15 L/tree	3.0 m
6	30 L/tree	4.0 m
10	50 L/tree	5.0 m
15	75 L/tree	6.0 m

Adjustment factors

Group	Condition	Factor
Gleba	Sandy gleba	0.90
Gleba	Loam	1.00
Gleba	Clay gleba	1.10
Spacing	Below 85% of referencyjny	0.85
Spacing	On the referencyjny curve	1.00
Spacing	Above 120% of referencyjny	1.20

The spacing factor is clamped to 0.85-1.20, and the tool warns when the value drifts outside the referencyjny curve.

How to read gleba type

Sandy gleba usually works better with shorter runs and more frequent cycles.
Loam is the baseline for this kalkulator, so the midpoint is easiest to read there.
Clay gleba can pond easily, so watch infiltration and avoid overfilling.

How to keep it region-neutral

The model does not use weather data, so the same logic can be used across regions.
If korona, pruning, root zone, or drainage differ a lot, fine-tune the target woda with field observation.
Start from the structure, then tune it in the field. That keeps the workflow simple.

Frequently asked questions

Can I use it without a target woda amount?

Yes. Leave target woda blank and the kalkulator uses the referencyjny midpoint built from tree age, spacing, and gleba.

Does tree spacing mean row spacing?

In this kalkulator, tree spacing means the distance to the next tree in the same row. It does not calculate row spacing area.

Does it use weather data or ET?

No. It is designed to stay practical by using only tree structure and kroplownik flow.

Can I switch between metric and US units?

Yes. You can switch between m / ft, L / gal, and L/h / gal/h.

Notice

This result is a guide. Korona, pruning, root zone, drainage, upał, wind, sun, and irrigation method all change the best value.
In sandy gleba, shorter runs and more frequent cycles are often safer. In clay, watch for ponding and slow infiltration.
If a manual target woda amount sits far outside the referencyjny range, check tree age and spacing again.