Kasangkapan sa Pagpapatuyo at Muling Pagpinta

Q: "Which temperature unit should I use, °C or °F?"

"Use the unit used by the site and the data sheet. Switching units converts the values."

Q: "The data sheet is based on 25°C / 77°F. Can I enter 20°C instead?"

"No. Enter the reference temperature exactly as stated in the data sheet."

Q: "What if the product does not list a latest recoat guideline?"

"Enter the same value as the minimum or leave it blank. Missing values are shown as partial results."

Q: "Can humidity be considered too?"

"Not in this initial version. Humidity is handled only as a caution note."

Q: "Can I reproduce the same inputs from a shared URL?"

"Yes. It restores the project name, temperature conditions, rows, and settings."

Q: "Can I use the PDF directly in a proposal?"

"Yes. The proposal layout is designed for print/PDF output."

Ayusin ang timing mula sa data sheet ayon sa temperatura sa site at ayusin ang iskedyul para sa proposal.

Ayusin ang mga timing mula sa data sheet ayon sa temperatura sa site at ipakita sa iisang lugar ang pinakamaagang muling pagpinta, pinakahuling gabay sa muling pagpinta, at pagkumpleto ng masking.

Gumamit ng °C / °F, at mag-export ng PDF na handa para sa proposal mula sa parehong screen.

Pag-aangkop sa temperatura

Saklaw ng muling pagpinta

Pagkumpleto ng masking

PDF export

Maraming wika

Paano Gamitin

Pumili ng unit ng temperatura at batayan, pagkatapos ay ilagay ang temperatura sa site.
Ilagay ang reference temperature, pinakamaagang muling pagpinta, pinakahuling muling pagpinta, at masking completion para sa bawat produkto.
Opsyonal na idagdag ang oras ng pagsisimula ng aplikasyon at suriin ang mga timestamp ng iskedyul.
Suriin ang mga resulta, pagkatapos ay kopyahin, ibahagi ang URL, o mag-export ng PDF.

Mga halimbawa

Pagtingin sa primer na 20°C sa 30°C

Input

Project: Exterior repaint / Site temp: 30°C / Reference temp: 20°C / Q10: 2.0 / Primer: 4-8h, masking 6h

Output

Salik ng temperatura 0.50, pinakamaagang muling pagpinta 2h, pinakahuling muling pagpinta 4h, masking na kumpleto sa 3h

Pagtingin sa top coat na 77°F sa 59°F

Input

Project: Shopfront repaint / Site temp: 59°F / Reference: 77°F / Q10: 2.0 / Top coat: 8-24h, masking 12h

Output

Salik ng temperatura 2.00, pinakamaagang muling pagpinta 16h, pinakahuling muling pagpinta 48h, masking na kumpleto sa 24h

Talasalitaan

Temperatura ng sanggunian: The temperature at which the data-sheet timing was specified.
Q10: The time-change multiplier for a 10°C shift. With 2.0, a 10°C drop roughly doubles the time and a 10°C rise roughly halves it.
Pinakamaagang muling pagpinta: The earliest recommended time to apply the next coat.
Pinakahuling gabay sa muling pagpinta: The upper end of the recoat window. If exceeded, surface preparation may be required.
Pagkompleto ng masking: The estimated time when protection or masking can be completed.

Mga Formula

temperatureFactor = Q10 ^ ((referenceTempC - siteTempC) / 10)
adjustedMinutes = referenceMinutes × temperatureFactor
targetTime = startTime + adjustedMinutes
Safe rounding: round earliest up, latest down, masking up

Notice (approximation only)

This is an estimate. Always prioritize the product data sheet and site conditions.
Humidity, ventilation, film thickness, substrate temperature, sunlight, wind, and mix ratio are not modeled precisely here.
If the reference temperature or basis differs from the data sheet, match the same basis before entering values.
The meaning of a recoat deadline varies by product. Check whether prep is required after the window closes.

FAQ

Which temperature unit should I use, °C or °F?

Use the unit used by the site and the data sheet. Switching units converts the values.

The data sheet is based on 25°C / 77°F. Can I enter 20°C instead?

No. Enter the reference temperature exactly as stated in the data sheet.

What if the product does not list a latest recoat guideline?

Enter the same value as the minimum or leave it blank. Missing values are shown as partial results.

Can humidity be considered too?

Not in this initial version. Humidity is handled only as a caution note.

Can I reproduce the same inputs from a shared URL?

Yes. It restores the project name, temperature conditions, rows, and settings.

Can I use the PDF directly in a proposal?

Yes. The proposal layout is designed for print/PDF output.