provera projektovanja etaža otvorenog kopa rudarstvo alati
otvoreni kop geometry
Srpski
English 日本語 ລາວ Монгол Oʻzbekcha Тоҷикӣ Кыргызча Қазақша Azərbaycan Հայերեն ქართული العربية Български Dansk Deutsch Ελληνικά Español Eesti Suomi Français हिन्दी ગુજરાતી ಕನ್ನಡ मराठी മലയാളം Srpski Slovenčina Slovenščina Kiswahili Hrvatski Indonesia Italiano 한국어 Lietuvių Latviešu Nederlands Norsk Svenska Polski Português Română Русский Українська Беларуская Shqip اردو தமிழ் తెలుగు Türkçe ภาษาไทย Tiếng Việt 简体中文 繁體中文 עברית ខ្មែរ Melayu မြန်မာ ਪੰਜਾਬੀ සිංහල Tagalog is

otvoreni kop geometry

Provera projektovanja etaža otvorenog kopa

Izračunajte ukupni ugao kosine iz visine etaže, širine bermа, ugla kosine i broja etaža.

Uporedite rezultat sa ciljanim uglom, vidite stanje bezbedno / blizu / opasno i pregledajte presek u pregledaču.

automatski-izračunaj the section geometry Show safe / near / danger at a glance Switch between metrički and imperijalni
Kako koristiti

Napomena o bezbednosti

  • This is a geometry checker, not a substitute for geotechnical stability analysis or rockfall analysis.
  • It checks the consistency of visina etaže, širina bermа, ugao kosine, and ukupni ugao kosine, but it does not judge legal compliance.
  • If the target comparison is near or on the danger side, always have a geotechnical reviewer confirm the design.
  • Water, blast damage, rock quality, equipment width, and drainage conditions are not part of this tool.

Kako koristiti

  1. 1 Enter visina etaže, širina bermа, ugao kosine, and etaža count.
  2. 2 dodaj a target ukupni ugao kosine if you want to uporedi the design against a reference angle.
  3. 3 Choose metrički or imperijalni, then otvori podešavanja if you want to change precision or sharing behavior.
  4. 4 Review the overall angle, the target margin, the exact-match values, and the previewed cross-section.
  5. 5 Use kopiraj rezultat, kopiraj URL za deljenje, resetuj, or the recent list to reuse the same condition later.

Primer

12 m etaža, 8 m berm, 70° face, 4 etažaes

Ulaz: visina etaže 12 m, širina bermа 8 m, ugao kosine 70°, etaža count 4, target ukupni ugao kosine 45°
izlaz: ukupni ugao kosine 49.2°, margin -4.2°, required širina bermа 10.2 m, danger side

The same geometry in imperijalni

Ulaz: visina etaže 39.37 ft, širina bermа 26.25 ft, ugao kosine 70°, etaža count 4, target ukupni ugao kosine 52°
izlaz: ukupni ugao kosine 49.2°, margin +2.8°, safe side

ČPP

Is the angle measured from the horizontal?

Yes. oboje the etaža ugao kosine and the ukupni ugao kosine are measured from the horizontal.

What happens when širina bermа is 0?

The overall angle moves zatvorir to the ugao kosine, but the tool still warns you because that is rarely practical in the polje.

What if the target angle cannot be matched exactly?

The required širina bermа or required ugao kosine can fall outside a workable range. In that case the exact-match helper shows that the target is not achievable with the current geometry.

Does this include local regulations or safety standards?

No. The tool stays limited to geometry and unit conversion so that it can be used globally without embedding local rules.

Can I work in oboje metrički and imperijalni units?

Yes. The unit switch pretvoris the visina etaže and širina bermа while keeping the geometry and the formulas the same.

Rečnik

visina etaže

The vertical height of one etaža.

širina bermа

The horizontal width between etažaes.

ugao kosine

The ugao kosine measured from the horizontal.

ukupni ugao kosine

The angle of the whole etaža stack when you look at the section from crest to toe.

Face setback

The horizontal run of one etaža face.

Formule

  • map[Text:face_run = h / tan(a) text:face_run = h / tan(a)]
  • map[Text:total_height = h × n text:total_height = h × n]
  • map[Text:total_run = (face_run × n) + (w × max(n - 1, 0)) text:total_run = (face_run × n) + (w × max(n - 1, 0))]
  • map[Text:overall_angle = atan(total_height / total_run) text:overall_angle = atan(total_height / total_run)]
  • map[Text:margin = target - overall_angle text:margin = target - overall_angle]
  • map[Text:required_berm_width = (total_height / tan(target) - n × face_run) / (n - 1) text:required_berm_width = (total_height / tan(target) - n × face_run) / (n - 1)]
  • map[Text:required_face_run = (total_height / tan(target) - (n - 1) × w) / n text:required_face_run = (total_height / tan(target) - (n - 1) × w) / n]
  • map[Text:required_face_angle = atan(h / required_face_run) text:required_face_angle = atan(h / required_face_run)]

Napomene

  • This tool does not cover water, blasting, rock quality, or equipment obrišiance.
  • If the target comparison is near the threshold, do not rely on rounding alone to make the decision.
  • If your site has a regional standard or company standard, folnisko that first.
  • Use this for geometrički checks only. A real slope design still needs a geotechnical review.
ukupni ugao kosine
—
Fix the visokolighted ulazs to reizračunaj.