Deschide Pit Banchet Design Verificăer Minerit Instrumente
Deschide pit geometry
Română
English 日本語 ລາວ Монгол Oʻzbekcha Тоҷикӣ Кыргызча Қазақша Azərbaycan Հայերեն ქართული العربية Български Dansk Deutsch Ελληνικά Español Eesti Suomi Français हिन्दी ગુજરાતી ಕನ್ನಡ मराठी മലയാളം Srpski Slovenčina Slovenščina Kiswahili Hrvatski Indonesia Italiano 한국어 Lietuvių Latviešu Nederlands Norsk Svenska Polski Português Română Русский Українська Беларуская Shqip اردو தமிழ் తెలుగు Türkçe ภาษาไทย Tiếng Việt 简体中文 繁體中文 עברית ខ្មែរ Melayu မြန်မာ ਪੰਜਾਬੀ සිංහල Tagalog is

Deschide pit geometry

Deschide Pit Banchet Design Verificăer

Calculează the overall pantă angle from banchet înălțime, berm lățime, face angle, and banchet count.

Compară the rezultat with a țintă angle, see the safe / near / danger status, and preview the section in the browser.

Auto-calculează the section geometry Afișează safe / near / danger at a glance Switch between metric and imperial
How to use

Siguranță notificare

  • This is a geometry verificator, not a substitute for geotechnical stability analysis or rockfall analysis.
  • It checks the consistency of banchet înălțime, berm lățime, face angle, and overall pantă angle, but it does not judge legal compliance.
  • If the țintă comparison is near or on the danger side, always have a geotechnical reviewer confirm the design.
  • Apă, blast damage, rock calitate, equipment lățime, and drainage conditions are not part of this instrument.

How to use

  1. 1 Enter banchet înălțime, berm lățime, face angle, and banchet count.
  2. 2 Add a țintă overall pantă angle if you want to compară the design against a reference angle.
  3. 3 Choose metric or imperial, then deschide Setări if you want to change precision or sharing behavior.
  4. 4 Review the overall angle, the țintă margin, the exact-match values, and the previewed cross-section.
  5. 5 Folosește Copiază rezultatul, Copiază URL-ul de partajare, Resetează, or the recent list to reuse the same condition later.

Exemplu

12 m banchet, 8 m berm, 70° face, 4 benches

Intrare: Banchet înălțime 12 m, berm lățime 8 m, face angle 70°, banchet count 4, țintă overall pantă angle 45°
Rezultat: Overall pantă angle 49.2°, margin -4.2°, required berm lățime 10.2 m, danger side

The same geometry in imperial

Intrare: Banchet înălțime 39.37 ft, berm lățime 26.25 ft, face angle 70°, banchet count 4, țintă overall pantă angle 52°
Rezultat: Overall pantă angle 49.2°, margin +2.8°, safe side

Întrebări frecvente

Is the angle measured from the horizontal?

Da. Both the banchet face angle and the overall pantă angle are measured from the horizontal.

What happens when berm lățime is 0?

The overall angle moves closer to the face angle, but the instrument still warns you because that is rarely practical in the field.

What if the țintă angle cannot be matched exactly?

The required berm lățime or required face angle can fall outside a workable range. In that case the exact-match helper shows that the țintă is not achievable with the curent geometry.

Does this include local regulations or siguranță standards?

Nu. The instrument stays limited to geometry and unitate conversion so that it can be used globally without embedding local rules.

Can I work in both metric and imperial unități?

Da. The unitate switch converts the banchet înălțime and berm lățime while keeping the geometry and the formulas the same.

Glossary

Banchet înălțime

The vertical înălțime of one banchet.

Berm lățime

The horizontal lățime between benches.

Face angle

The face angle measured from the horizontal.

Overall pantă angle

The angle of the whole banchet stack when you look at the section from crest to toe.

Face setback

The horizontal run of one banchet face.

Formulas

  • map[Text:face_run = h / tan(a) text:face_run = h / tan(a)]
  • map[Text:total_height = h × n text:total_height = h × n]
  • map[Text:total_run = (face_run × n) + (w × max(n - 1, 0)) text:total_run = (face_run × n) + (w × max(n - 1, 0))]
  • map[Text:overall_angle = atan(total_height / total_run) text:overall_angle = atan(total_height / total_run)]
  • map[Text:margin = țintă - overall_angle text:margin = țintă - overall_angle]
  • map[Text:required_berm_width = (total_height / tan(țintă) - n × face_run) / (n - 1) text:required_berm_width = (total_height / tan(țintă) - n × face_run) / (n - 1)]
  • map[Text:required_face_run = (total_height / tan(țintă) - (n - 1) × w) / n text:required_face_run = (total_height / tan(țintă) - (n - 1) × w) / n]
  • map[Text:required_face_angle = atan(h / required_face_run) text:required_face_angle = atan(h / required_face_run)]

Nutes

  • This instrument does not cover apă, blasting, rock calitate, or equipment clearance.
  • If the țintă comparison is near the threshold, do not rely on rounding alone to make the decision.
  • If your site has a regional standard or company standard, follow that first.
  • Folosește this for geometric checks only. A real pantă design still needs a geotechnical review.
Overall pantă angle
—
Fix the highlighted inputs to recalculate.