Pemeriksa Desain Bench Tambang Terbuka Alat Pertambangan
Geometri tambang terbuka
Indonesia
English 日本語 ລາວ Монгол Oʻzbekcha Тоҷикӣ Кыргызча Қазақша Azərbaycan Հայերեն ქართული العربية Български Dansk Deutsch Ελληνικά Español Eesti Suomi Français हिन्दी ગુજરાતી ಕನ್ನಡ मराठी മലയാളം Srpski Slovenčina Slovenščina Kiswahili Hrvatski Indonesia Italiano 한국어 Lietuvių Latviešu Nederlands Norsk Svenska Polski Português Română Русский Українська Беларуская Shqip اردو தமிழ் తెలుగు Türkçe ภาษาไทย Tiếng Việt 简体中文 繁體中文 עברית ខ្មែរ Melayu မြန်မာ ਪੰਜਾਬੀ සිංහල Tagalog is

Geometri tambang terbuka

Pemeriksa Desain Bench Tambang Terbuka

Calculate the overall slope angle from bench height, berm width, face angle, and bench count.

Bandingkan hasilnya dengan sudut target, lihat status aman / mendekati / bahaya, dan tinjau penampang di browser.

Auto-calculate the section geometry Show safe / near / danger at a glance Switch between metric and imperial
How to use

Safety notice

  • This is a geometry checker, not a substitute for geotechnical stability analysis or rockfall analysis.
  • It checks the consistency of bench height, berm width, face angle, and overall slope angle, but it does not judge legal compliance.
  • If the target comparison is near or on the danger side, always have a geotechnical reviewer confirm the design.
  • Water, blast damage, rock quality, equipment width, and drainage conditions are not part of this tool.

How to use

  1. 1 Enter bench height, berm width, face angle, and bench count.
  2. 2 Add a target overall slope angle if you want to compare the design against a reference angle.
  3. 3 Choose metric or imperial, then open Settings if you want to change precision or sharing behavior.
  4. 4 Review the overall angle, the target margin, the exact-match values, and the previewed cross-section.
  5. 5 Use Copy result, Copy share URL, Reset, or the recent list to reuse the same condition later.

Contoh

12 m bench, 8 m berm, 70° face, 4 benches

Input: Bench height 12 m, berm width 8 m, face angle 70°, bench count 4, target overall slope angle 45°
Output: Overall slope angle 49.2°, margin -4.2°, required berm width 10.2 m, danger side

The same geometry in imperial

Input: Bench height 39.37 ft, berm width 26.25 ft, face angle 70°, bench count 4, target overall slope angle 52°
Output: Overall slope angle 49.2°, margin +2.8°, safe side

Tanya jawab

Is the angle measured from the horizontal?

Yes. Both the bench face angle and the overall slope angle are measured from the horizontal.

What happens when berm width is 0?

The overall angle moves closer to the face angle, but the tool still warns you because that is rarely practical in the field.

What if the target angle cannot be matched exactly?

The required berm width or required face angle can fall outside a workable range. In that case the exact-match helper shows that the target is not achievable with the current geometry.

Does this include local regulations or safety standards?

No. The tool stays limited to geometry and unit conversion so that it can be used globally without embedding local rules.

Can I work in both metric and imperial units?

Yes. The unit switch converts the bench height and berm width while keeping the geometry and the formulas the same.

Glosarium

Bench height

The vertical height of one bench.

Berm width

The horizontal width between benches.

Face angle

The face angle measured from the horizontal.

Overall slope angle

The angle of the whole bench stack when you look at the section from crest to toe.

Face setback

The horizontal run of one bench face.

Formulas

  • map[Text:face_run = h / tan(a) text:face_run = h / tan(a)]
  • map[Text:total_height = h × n text:total_height = h × n]
  • map[Text:total_run = (face_run × n) + (w × max(n - 1, 0)) text:total_run = (face_run × n) + (w × max(n - 1, 0))]
  • map[Text:overall_angle = atan(total_height / total_run) text:overall_angle = atan(total_height / total_run)]
  • map[Text:margin = target - overall_angle text:margin = target - overall_angle]
  • map[Text:required_berm_width = (total_height / tan(target) - n × face_run) / (n - 1) text:required_berm_width = (total_height / tan(target) - n × face_run) / (n - 1)]
  • map[Text:required_face_run = (total_height / tan(target) - (n - 1) × w) / n text:required_face_run = (total_height / tan(target) - (n - 1) × w) / n]
  • map[Text:required_face_angle = atan(h / required_face_run) text:required_face_angle = atan(h / required_face_run)]

Catatan

  • Alat ini tidak mencakup air, peledakan, kualitas batuan, atau kelonggaran peralatan.
  • Jika perbandingan target berada dekat ambang, jangan mengandalkan pembulatan saja untuk mengambil keputusan.
  • Jika lokasi Anda memiliki standar regional atau standar perusahaan, ikuti itu terlebih dahulu.
  • Gunakan ini hanya untuk pemeriksaan geometri. Desain lereng nyata tetap memerlukan tinjauan geoteknik.
Overall slope angle
—
Fix the highlighted inputs to recalculate.