Tile & Flooring Layout Calculator (Offcuts कम करें)
Room और material dimensions से edge cut widths, required tile count, और waste rate जल्दी निकालें।
Minimum offcuts और visual symmetry के बीच संतुलन देखने के लिए 2-3 options की तुलना करें।
उपयोग कैसे करें
- Room dimensions (L/W), material dimensions (A/B), और joint width दर्ज करें।
- Direction (long-side orientation) और offset mode (centered या one-side flush) चुनें।
- Candidate cards को waste rate, minimum cut, और balance के आधार पर तुलना करें।
- चयनित option के लिए detailed numbers और cut-position diagram देखें।
- उसी layout conditions पर site members या clients से चर्चा करने के लिए share URL कॉपी करें।
नमूने
600x300 tile, 3 mm joint
इनपुट: Room 5400x3600 mm, tile 600x300 mm, direction = room length के along long side, offset = centered
आउटपुट: Options A/B/C में count, waste rate, और minimum cut की तुलना करें, फिर cut positions देखें
1818x303 flooring, 0 joint
इनपुट: Room 4550x2730 mm, material 1818x303 mm, offset = one-side flush (left-bottom origin)
आउटपुट: Flush layout में offcut location और minimum-cut threshold के उल्लंघन की जाँच करें
सूत्र
P_x = TileX + J, P_y = TileY + JFlush: N = ceil((Room + J) / (Tile + J)), CutEnd = Room - (N - 1) * (Tile + J)Centered: Cut = (Room - (N - 2) * Tile - (N - 1) * J) / 2TotalTiles = N_x * N_yWasteRate = (A_buy - A_used) / A_buy
अक्सर पूछे जाने वाले प्रश्न
मैं अधिक waste rate वाले option को क्यों चुनूँ?
क्योंकि waste rate अकेला मानदंड नहीं है। आपके project में visual symmetry या बहुत छोटे fragile cuts से बचना अधिक महत्वपूर्ण हो सकता है।
Centered और one-side flush में क्या अंतर है?
Centered appearance के लिए दोनों sides पर edge cuts को बराबर रखता है। One-side flush start side से full tiles को प्राथमिकता देता है और cuts को opposite side पर भेजता है।
क्या waste rate वास्तविक on-site discard के बराबर है?
हमेशा नहीं। यदि offcuts को दूसरी rows में reuse किया जा सके, तो actual discard इस estimate से कम हो सकती है।
Field adjustment अभी भी क्यों ज़रूरी है?
Cut-ins, दीवारों की irregularity, trim positions, और movement-joint requirements केवल simple geometric calculation से पूरी तरह तय नहीं हो सकतीं।
क्या मैं room dimensions को meters में दर्ज कर सकता हूँ?
हाँ। Inputs m या mm दोनों में हो सकते हैं, और internal calculation mm में unify की जाती है।
नोट्स
- यह tool rough layout estimator है। इसे final installation dimensions के रूप में उपयोग न करें।
- Waste rate एक conservative estimate है, जो offcut reuse नहीं मानती। वास्तविक discard कम हो सकती है।
- Cut-ins, दीवार की unevenness, trim positions, और movement joints की पुष्टि site पर करनी होगी।